v2.2.9-5-mag2000-iag802-normal-iac-v16-squashfs-sdcard-0c7e4fec.img * Added cfgdefault configurations for custom models to MAG2100. * Added DTMF caller ID support for analog gateway FXS ports. v2.2.9-4-mag2000-iag802-normal-iac-v16-squashfs-sdcard-ee091251.zip * Fixed incorrect time issues on HB1981 Analog and E1 modules * Fixed FXS server break internal exchange issue * Fixed MAG2100 device FXS port settings page abnormal issue * Fixed IP2TEL routing destination device port filling support * Added policy configuration support to FXO analog gateway routing configuration page * Added OIAD FXS support for sending caller ID before ring * Added local time synchronization function * Added L304 and future SPI-NAND OEM partition support of extended files * Added emetrotel custom firmware xstim support of server hotline * Added missing 403 retry functionality in version 2.2.9 hotfix * Added comments to trunk configuration identify_prefix parameter page and adjusted interface parameter descriptions * Added friendly prompt information to network management access options * Optimized TR069 requirements * Optimized log management system * Optimized when analog gateway hotline number adds # and number map sets # as send key * Optimized dialtone_detect to solve slow channel release when calling PSTN to IAD FXO and caller hangs up immediately * Optimized login page display when OEM style is blue_right and blue_center * Optimized SRV record description * Upgraded ICVP project check_input2 v2.2.9-mag2000-iag802-normal-iac-v16-squashfs-sdcard-162b26b5.img *Fixed the problem that single E1 Gateway/Analog MAG1000 Insufficient Memory Resources *Fixed the problem that registration fails after reaching server max_contacts Limit *Fixed the problem of FXS port settings batch configuration *Fixed the problem of IMS incoming call "To" number mismatch handling *Fixed the problem of web template qualify authentication logic inverted *Fixed the problem of FXO caller id Garbled Text *Fixed the problem of popping noise When Analog Phone Off-Hook *Fixed the problem of no caller id *Fixed the problem that MAG1000 Resource Leak After 77 Days of Operation *Fixed the problem that FXO CDR Port Field Display Timing *Fixed the problem that analog Phone Time Retrieval Incorrect via NetBus FXO Gateway Board *Added MAG1100/2100 Driver Compatibility for Versions Without Port Lights *Added UScale S132 OEM (MAG2000) and default cfg *Added FXO Gateway CallRoute Support for Group Call Source *Added support for IMS dual homing with same contact *Added "Select All" option in FOX port setting *Added local DNS SRV resolution for multi-server single registration *Added UAC support for tel protocol header *Added OIAD OEM UScale S196 & S1224 firmware *Added called number transformation *Added TR069 *Optimized automated deployment *Optimized dial rule *Optimized CDR query list v2.2.8-mag2000-iag802-normal-iac-v16-squashfs-sdcard-f416c8a7.img *Fixed the problem that the device has been running for a period of time and cannot make normal outgoing calls *Fixed the problem that when there is a message on individual channels, the 5288 caller will go off-hook abnormally; Channel 2 goes off-hook without sound *Fixed the problem that call hangs up directly when timeout parameter calltimeout is set to 0 *Fixed the problem that there is no beep after power off when there is MWI, *Fixed the problem that sending multiple registration requests resulting in rejection when connect with grandstream pbx *Fixed the problem that IMS line inbound To number does not match registration number *Fixed the problem that ports configured in do-not-disturb mode can cause number feed failure *Fixed the problem that interface request timeout causes the web page to force quit *Fixed the problem that port status voltage value does not correspond to port number *Fixed the problem that password change screen doesn't prompt for a password format *Fixed the problem that clicking disable again fails to save after opening OpenVPN *Fixed the problem of unconditional transfer failure. *Fixed MAC address problem *Fixed the problem that two H3 ip addresses in PCB will conflict *Fixed the problem that package dependency and naming exception under ovapp *Added temporary answer 180 parameter after adding invite *Added ringing state in FXS port status *Added XSTIM protocol support *Added custom Sync Down *Added comment to cfgdefault file *Added usecallerid parameter to FXO port for devices like door phone or alarm panel *Added support for tel in UAC *Added default.cfg and OEM *Opened SNMP mib *Optimized language *Optimized page display *Optimized analog FXS/FXO display status v2.2.7-mag2000-iag802-normal-iac-v16-squashfs-sdcard-865501ae.img *Fixed the problem of P-Asserted-Identity callerid. *Fixed the problem of ocloudclient and icvp http_set coupling *Fixed the problem that firewall is unable to fill in icmp type when selecting ICMP protocols *Fixed the problem that Static routes for network functions does not support management port *Fixed the problem that system related sys_* classes upgraded to check_input2 checking *Fixed the problem that log management_support log page save without prompting *Fixed the problem that Dual NIC bridge network mode, /usr/sbin/odhcpd process reporting error *Fixed the problem that firmware download via server is not working on some HTTPS servers. *Fixed the problem that some sip servers are treating registrations with different line parameters as new registrations, resulting in registrations being rejected *Fixed the problem that FXO group number is not shown in port status page *Fixed the problem that after configuring Softethervpn in VPN settings page, the web will force logout when getting the configuration information again *Fixed the problem that network status page does not show lan port information. *Added support for chinese voice *Added TLS1.3 *Added pvid parameter in switch device *Added HWFXO/FXS GAIN parameter *Added cloud management account registration reminder message in cloud management setting page *Added function that FXO will not answer the incoming call by default, and the waiting time before answering can be set. *Added display of ICVP slot information *Added Self-Switching VEX *Added upnp *Added mtu option setting *Opened MWI voltage parameter for user's self-configuration *Optimized OIAD self-switching feature. *Optimized jffs2_fixup *Optimized English translation of light effect *Optimized ims registration speed *Changed Network information initialization part to json way to deal with the difference, including API interface reading. *Adapted MAG2000